这是描述信息
搜索
确认
取消
NEWS CENTER
please try again.

Color coated board roof is a new type of panel

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2020-10-13
  • Views:0

(Summary description)Color-coated board roof is a new type of panel, which is considered to be the most ideal material for modern buildings and has a relatively long life. There are many precautions for installing color-coated board roofs as bottom plates. Professional construction masters are required to install. Aluminum-magnesium-manganese roofing panels are made of aluminum-magnesium-manganese plates. This type of material will not corrode even if it is used for a long time. Under normal conditions, it can be used for forty years, so as not to affect the future use effect. The specific installation precautions are as follows:

Before installation, it is necessary to clean up the contamination of the color-coated board roof to avoid corrosion of the panel. In addition, pay attention to the flatness of the panel during installation, and there should be no bending and deformation. The color-coated board roof overlaps a wave crest, so it has been recognized by many users. The entire system of aluminum-magnesium-manganese roof panels adopts a mechanized seaming mode, so that water leakage can be avoided, and it has a good elimination system, especially in heavy rain weather, which can drain water in time. It can avoid the huge pressure caused by the extrusion of water, and can prevent the deformation of the project. This will be firmer and will not leak water. It is best to be anchored reliably, the installation should be kept flat, and there should be no gaps between the plates.

Color-coated board roofing and floor installation need to be from high to low, and the design of the lightning protection system is familiar. The roof panel can be used as an air-termination device alone without the need for lightning protection belts. It can also be used in conjunction with avoidance belts or lightning rods to form a safe multiple lightning protection system; the installation method from the middle part to the edge, the overlap method is from low to high. After the floor installation starting line is installed, select self-tapping screws to confine both ends, and then install the second board. It is necessary to install the second color-coated board roof to make a mark, check whether the board has deviations, and need to meet the design requirements, if it cannot meet the needs, adjust it, and then fully tighten it. After installation, pay attention to check whether there are any omissions. If the tightening is not enough, there will be rain leakage, so be careful.

Color coated board roof is a new type of panel

(Summary description)Color-coated board roof is a new type of panel, which is considered to be the most ideal material for modern buildings and has a relatively long life. There are many precautions for installing color-coated board roofs as bottom plates. Professional construction masters are required to install. Aluminum-magnesium-manganese roofing panels are made of aluminum-magnesium-manganese plates. This type of material will not corrode even if it is used for a long time. Under normal conditions, it can be used for forty years, so as not to affect the future use effect. The specific installation precautions are as follows:

Before installation, it is necessary to clean up the contamination of the color-coated board roof to avoid corrosion of the panel. In addition, pay attention to the flatness of the panel during installation, and there should be no bending and deformation. The color-coated board roof overlaps a wave crest, so it has been recognized by many users. The entire system of aluminum-magnesium-manganese roof panels adopts a mechanized seaming mode, so that water leakage can be avoided, and it has a good elimination system, especially in heavy rain weather, which can drain water in time. It can avoid the huge pressure caused by the extrusion of water, and can prevent the deformation of the project. This will be firmer and will not leak water. It is best to be anchored reliably, the installation should be kept flat, and there should be no gaps between the plates.

Color-coated board roofing and floor installation need to be from high to low, and the design of the lightning protection system is familiar. The roof panel can be used as an air-termination device alone without the need for lightning protection belts. It can also be used in conjunction with avoidance belts or lightning rods to form a safe multiple lightning protection system; the installation method from the middle part to the edge, the overlap method is from low to high. After the floor installation starting line is installed, select self-tapping screws to confine both ends, and then install the second board. It is necessary to install the second color-coated board roof to make a mark, check whether the board has deviations, and need to meet the design requirements, if it cannot meet the needs, adjust it, and then fully tighten it. After installation, pay attention to check whether there are any omissions. If the tightening is not enough, there will be rain leakage, so be careful.

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2020-10-13
  • Views:0
Information

Color-coated board roof is a new type of panel, which is considered to be the most ideal material for modern buildings and has a relatively long life. There are many precautions for installing color-coated board roofs as bottom plates. Professional construction masters are required to install. Aluminum-magnesium-manganese roofing panels are made of aluminum-magnesium-manganese plates. This type of material will not corrode even if it is used for a long time. Under normal conditions, it can be used for forty years, so as not to affect the future use effect. The specific installation precautions are as follows:

Before installation, it is necessary to clean up the contamination of the color-coated board roof to avoid corrosion of the panel. In addition, pay attention to the flatness of the panel during installation, and there should be no bending and deformation. The color-coated board roof overlaps a wave crest, so it has been recognized by many users. The entire system of aluminum-magnesium-manganese roof panels adopts a mechanized seaming mode, so that water leakage can be avoided, and it has a good elimination system, especially in heavy rain weather, which can drain water in time. It can avoid the huge pressure caused by the extrusion of water, and can prevent the deformation of the project. This will be firmer and will not leak water. It is best to be anchored reliably, the installation should be kept flat, and there should be no gaps between the plates.

Color-coated board roofing and floor installation need to be from high to low, and the design of the lightning protection system is familiar. The roof panel can be used as an air-termination device alone without the need for lightning protection belts. It can also be used in conjunction with avoidance belts or lightning rods to form a safe multiple lightning protection system; the installation method from the middle part to the edge, the overlap method is from low to high. After the floor installation starting line is installed, select self-tapping screws to confine both ends, and then install the second board. It is necessary to install the second color-coated board roof to make a mark, check whether the board has deviations, and need to meet the design requirements, if it cannot meet the needs, adjust it, and then fully tighten it. After installation, pay attention to check whether there are any omissions. If the tightening is not enough, there will be rain leakage, so be careful.

Scan the QR code to read on your phone

CONTACT US
 

International Marketing Department
——

TEL:
0086-13506663511 Mr Zhou
Whatsapp:
0086-13506663511
E-mail: icl@china-ppgi.com
HTTP: www.china-ppgi.com
ADD:Dianzi Town Industrial Park, Boxing County, Binzhou City, Shandong Province

 

CONTACT US
 

Domestic Marketing Department
——

TEL/Whatsapp:
13365436523 Mr Guo
TEL:
0543-7022661
E-mail: sales@china-ppgi.com
HTTP: www.china-ppgi.com

ADD:Dianzi Town Industrial Park, Boxing County, Binzhou City, Shandong Province

 

COPYRIGHT © 2021 SHENGHONG STEEL  ALL RIGHTS RESERVED.   [ 鲁ICP备20206335号